While NetApp keeps improving the front end that is ActiveIQ, for both pre-sales and support purposes, I constantly find myself going into the Classic AutoSupport and accessing the raw autosupport data; most often it’s sysconfig -a. Recently I was trying to explain the contents to a co-worker and I realized that I should just document it as a blog post. So here is sysconfig explained.
The command sysconfig -a is the old 7-mode command to give you all the hardware information from the point of view of ONTAP. All the onboard ports are assigned to “slot 0” whereas slot 1-X are the physical PCIe slots where myriad cards can be inserted. Here’s one example, I’ll insert comments as I feel it is appropriate.
This first section is some very basic info about the motherboard, it gives you the CPU, RAM and serial number as well as the IP address of the SP or BMC, depending on the model:
Backplane Serial Number: 012345678901
slot 0: System Board 2.0 GHz (System Board XX E0)
Model Name: FAS8020
Part Number: 111-01099
Revision: E0
Serial Number: 012345678901
BIOS version: 9.3
Loader version: 5.3
SEQ CPLD version: 1.14
NVRAM CPLD version: 1.0
Processors: 6
Processor ID: 0x206d7
Microcode Version: 0x710
Processor type: Intel(R) Xeon(R) CPU E5-2620 @ 2.00GHz
Memory Size: 24576 MB
Memory Attributes: Bank Interleaving
Hoisting
Channel Interleaving
Chipkill ECC
CMOS RAM Status: OK
Controller: A
PCIE Switch 0: id 0 8020 4.02
Service Processor Status: Online
Firmware Version: 3.1.2P1
Mgmt MAC Address: 00:A0:98:A2:xx:0A
Ethernet Link: up, full duplex, auto-neg complete
Using DHCP: no
IPv4 configuration:
IP Address: 169.0.7.8
Netmask: 255.255.255.0
Gateway: 169.0.7.1
IPv6 configuration: Disabled
Here’s the rest of the onboard ports, as evidenced by the slot 0 reference. This first one is the external RJ-45 ports “Wrench” and “Locked wrench”, Wrench is a switch port that feeds e0M and the Service Processor (SP), Locked Wrench feeds e0P:
slot 0: Internal 10/100/1000 Ethernet Switch
Firmware Version: Version2 SB_XX Switch0
Locked-wrench: auto-100tx-fd-up
Wrench: auto-1000t-fd-up
Device Type: 88E6176
memory mapped I/O base 0x0000000045f00000, size 0x20000
I/O base 0x0000000000003000, size 0x20
memory mapped I/O base 0x0000000045f20000, size 0x4000
Here’s the back of an 8020, you’ll see above the port covered in a black circle is a picture of a wrench, ie: “wrench port” and below that is port labelled with a wrench covered by a lock, ie: “locked wrench”.
While the SP Ethernet connection isn’t mentioned further, the two Ethernet ports viewable by ONTAP are indicated below. e0M is for management of the host and e0P is used in older versions of ONTAP to run ACP on the attached disk shelves:
slot 0: Internal 10/100/1000 Ethernet Controller
e0M MAC Address: 00:a0:98:a2:xx:08 (auto-1000t-fd-up)
e0P MAC Address: 00:a0:98:a2:xx:09 (auto-100tx-fd-up)
Device Type: Rev 0
Firmware Version: 2.1
memory mapped I/O base 0x0000000046000000, size 0x20000
I/O base 0x0000000000004000, size 0x20
memory mapped I/O base 0x0000000046020000, size 0x4000
Here we have the two onboard 10Gbit, SFP+ based ports, e0a and e0b. You can see that they’re using TwinAx, you can even see the manufacturer of the SFP+ built into the TwinAx:
slot 0: 10 Gigabit Ethernet Controller IX1-SFP+
e0a MAC Address: 00:a0:98:a2:xx:1e (auto-10g_twinax-fd-up)
SFP Vendor: Molex Inc.
SFP Part Number: 747529718
SFP Serial Number: 5304318xx
e0b MAC Address: 00:a0:98:a2:xx:1f (auto-10g_twinax-fd-up)
SFP Vendor: Amphenol
SFP Part Number: 628620000
SFP Serial Number: APF160300595xx
Device Type: 82599
Firmware Version: 4.2-2
memory mapped I/O base 0x46220000, size 0x20000
I/O base 0x0000000000006020, size 0x20
memory mapped I/O base 0x46244000, size 0x4000
memory mapped I/O base 0x46200000, size 0x20000
I/O base 0x0000000000006000, size 0x20
memory mapped I/O base 0x46240000, size 0x4000
prefetchable memory base 0x45600000, size 0x200000
prefetchable memory base 0x45c10000, size 0x2000
Here are the two CNA ports, e0c and e0d, both in 10Gbit mode, also using TwinAx. These two ports will come up again below:
slot 0: 1G/10G Ethernet Controller CNA EP 8324
(Dual-port, QLogic CNA 8324(8362) rev. 2)
e0c MAC Address: 00:a0:98:a2:xx:00 (auto-10g_twinax-fd-up)
e0d MAC Address: 00:a0:98:a2:xx:01 (auto-10g_twinax-fd-up)
Device Type: EP8324N
NIC Firmware rev: 5.4.56.0
prefetchable memory base 0x45800000, size 0x200000
prefetchable memory base 0x45c12000, size 0x2000
There are two onboard, 1Gbit, RJ-45 ports, unused on this host:
slot 0: Dual Gigabit Ethernet Controller 82580
e0e MAC Address: 00:a0:98:a2:xx:06 (auto-unknown-down)
e0f MAC Address: 00:a0:98:a2:xx:07 (auto-unknown-down)
Device Type: 1516
Firmware Version: 3.29, 0x8000021A
memory mapped I/O base 0x0000000045d00000, size 0x80000
I/O base 0x0000000000002000, size 0x20
memory mapped I/O base 0x0000000045e00000, size 0x4000
memory mapped I/O base 0x0000000045d80000, size 0x80000
I/O base 0x0000000000002020, size 0x20
memory mapped I/O base 0x0000000045e04000, size 0x4000
Here is the NVRAM card, complete with battery status:
slot 0: NVRAM (NVRAM 9) Revision: C0 Serial Number: 0216050495xx DIMM Size: 4096 MB Memory Size: 4096 MB Battery Status: Battery sufficiently charged Running Firmware: 1.3.0
Here are the onboard SAS ports, with a sub-section for each port. Each port has four connections called “Phys”, numbered (0-3). The defintion of a Phy is:
Phy. Phys are part of the physical connection between SAS devices. Each phy contains a transceiver that sends data back and forth between SAS devices. Phys are internal, within SAS connectors.
Each port will show you the type of connector inserted which you can map to a cable type, the first one below (112-00178+A0) is a 5M SAS cable, it also show you a list of all drives connected to it. The XX.YY number at the start of each drive line is the shelf number (XX), then the drive number (YY) in the shelf. At the end, is the drive’s serial number, each serial number will appear twice in this output because it is connected via two ports. You’ll see the first drive below with serial YGH5M99A is also the first drive in the list connected to port A of card 1. Since there’s 24 drives per shelf in this example, I’ve only included the first two and last two drives from every shelf.
Here’s port A of the two SAS ports in slot 0 (onboard):
slot 0: SAS Host Adapter 0a (PMC-Sierra PM8001 rev. C, SAS, )
Firmware rev: 01.12.06.00
Base WWN: 5:00a098:003xxxx:b8
Phy State: [0] Enabled, 3.0 Gb/s
[1] Enabled, 3.0 Gb/s
[2] Enabled, 3.0 Gb/s
[3] Enabled, 3.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00178+A0
QSFP Type: Passive Copper 5m ID:01
QSFP Serial Number: 610320331
01.0 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH5M99A)
01.1 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH3SWVA)
<SNIP>
01.22: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH527SA)
01.23: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH56XAA)
02.0 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1XN2Y)
02.1 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1YZGY)
<SNIP>
02.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1XVSG)
02.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1V8GH)
03.0 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TLAR)
03.1 : NETAPP X306_HAKPE02TSSM NA00 1695.4GB 512B/sect (K5HEVP9D)
<SNIP>
03.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1VARR)
03.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TH3C)
04.0 : NETAPP X306_HAKPE02TSSM NA00 1695.4GB 512B/sect (K5HEU7YD)
04.1 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TM21)
<SNIP>
04.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TRZ3)
04.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1YYTT)
Shelf 1: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 2: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 3: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 4: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Here is port B of the same card, you can see this one is plugged into an IOM6 module, the above is plugged into an IOM3:
slot 0: SAS Host Adapter 0b (PMC-Sierra PM8001 rev. C, SAS, )
Firmware rev: 01.12.06.00
Base WWN: 5:00a098:003xxxx:bc
Phy State: [4] Enabled, 6.0 Gb/s
[5] Enabled, 6.0 Gb/s
[6] Enabled, 6.0 Gb/s
[7] Enabled, 6.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00177+A0
QSFP Type: Passive Copper 2m ID:01
QSFP Serial Number: 326822103
20.0 : NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJRBE5X)
20.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (NHGEH93Y)
<SNIP>
20.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (N8G7XTBM)
20.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (N8G7XU4M)
21.0 : NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJPZ6KX)
21.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (NHGEGGZY)
<SNIP>
21.22: NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJPVEKX)
21.23: NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJR1W4X)
22.0 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JBNWDB)
22.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAEPNB)
<SNIP>
22.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAKZVB)
22.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAZXKB)
23.0 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4J7MJEB)
23.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JBAP3B)
<SNIP>
23.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JDPD5B)
23.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JDNPPB)
Shelf 20: DS4246 Firmware rev. IOM6 A: 0181 IOM6 B: 0181
Shelf 21: DS4246 Firmware rev. IOM6 A: 0181 IOM6 B: 0181
Shelf 22: DS4246 Firmware rev. IOM6 A: 0191 IOM6 B: 0191
Shelf 23: DS4246 Firmware rev. IOM6 A: 0191 IOM6 B: 0191
memory mapped I/O base 0x46330000, size 0x10000
memory mapped I/O base 0x46320000, size 0x10000
memory mapped I/O base 0x0000000046310000, size 0x10000
memory mapped I/O base 0x0000000046300000, size 0x10000
Now you can see the two onboard FC ports are unused, these are the same physical ports as the CNAs above, that’s why they have the same slot and port name 0c and 0d, the Ethernet profile of these ports are e0c and e0d. The FC ports below are unused because they are in use as pure Ethernet adapters above:
slot 0: Fibre Channel Target Host Adapter 0c
(QLogic CNA 8324 (8362) rev. 2, )
Firmware rev: 8.1.0
Flash rev: 3.1.0
Host Port Addr: 000000
FC Nodename: 50:0a:09:80:80:b1:xx:1c (500a098080b1xx1c)
FC Portname: 50:0a:09:82:80:b1:xx:1c (500a098280b1xx1c)
Connection: No link
Switch Port: Unknown
SFP Vendor Name: CISCO-MOLEX
SFP Vendor P/N: 74752-9731
SFP Vendor Rev: 09
SFP Serial No.: MOC1947A1BU
SFP Connector: Passive Copper
SFP Capabilities: 10 Gbit/Sec
prefetchable memory base 0x45c0c000, size 0x2000
prefetchable memory base 0x45c00000, size 0x4000
prefetchable memory base 0x45a00000, size 0x100000
slot 0: Fibre Channel Target Host Adapter 0d
(QLogic CNA 8324 (8362) rev. 2, )
Firmware rev: 8.1.0
Flash rev: 3.1.0
Host Port Addr: 000000
FC Nodename: 50:0a:09:80:80:b1:xx:1c (500a098080b1xx1c)
FC Portname: 50:0a:09:81:80:b1:xx:1c (500a098180b1xx1c)
Connection: No link
Switch Port: Unknown
SFP Vendor Name: CISCO-MOLEX
SFP Vendor P/N: 74752-9731
SFP Vendor Rev: 09
SFP Serial No.: MOC1947A15C
SFP Connector: Passive Copper
SFP Capabilities: 10 Gbit/Sec
prefetchable memory base 0x45c0e000, size 0x2000
prefetchable memory base 0x45c04000, size 0x4000
prefetchable memory base 0x45b00000, size 0x100000
The next entry is the backplane connection between the two controllers in an HA pair, on this model it is InfiniBand, but can be other protocols on different platforms:
slot 0: IB Host Adapter i0 (Mellanox ConnectX MT27518 rev. 0)
Running Firmware: 2.11.534
Debug Firmware: No
Interconnect Port 1:
Default GID: fe80:0000:0000:0000:00a0:9800:0033:e334
Base LID: 0x334
SM LID: 0x0
Active MTU: 4096
Data Rate: 40 Gb/s (4X) QDR
Link State: ACTIVE
Interconnect Port 2:
Default GID: fe80:0000:0000:0000:00a0:9800:0033:e335
Base LID: 0x335
SM LID: 0x0
Active MTU: 4096
Data Rate: 40 Gb/s (4X) QDR
Link State: ACTIVE
memory mapped I/O base 0x44a00000, size 0x100000
prefetchable memory base 0x44000000, size 0x800000
The final device onboard for this model is a USB-connected storage device for booting the platform, previous platforms used CF cards since they are IDE-native and new ones use .m2.
slot 0: Intel USB EHCI Adapter u0a (0x46420000)
boot0 Micron Technology 0x655, class 0/0, rev 2.00/11.16, addr 2 7744MB 512B/sect (10F0082700169688)
memory-mapped I/O base 0x46420000, size 0x00000400
This platform (FAS8020) only has two PCI slots, this particular one only has a card in slot 1, a 4 port SAS card. You’ll find it displays all the same information as the onboard one above, and here’s where you’ll find drives repeating for their second path: Slot 1, port A:
slot 1: SAS Host Adapter 1a (PMC-Sierra PM8072 rev. C, SAS, )
MFG Part Number: NetApp, Inc. 110-00401 rev. A0
Part number: 111-02026+A1
Serial number: 031616001350
Date Code: 20160416
Firmware rev: 03.07.11.00
Base WWN: 5:00a098:006xxxx:10
Phy State: [12] Enabled, 3.0 Gb/s
[13] Enabled, 3.0 Gb/s
[14] Enabled, 3.0 Gb/s
[15] Enabled, 3.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00178+A0
QSFP Type: Passive Copper 5m ID:00
QSFP Serial Number: 610320093
05.0 : NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0912384)
05.1 : NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0923740)
<SNIP>
05.22: NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0890897)
05.23: NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0923803)
06.0 : NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1G9BA)
06.1 : NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1GANV)
<SNIP>
06.22: NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1FV2F)
06.23: NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1FTYM)
07.0 : NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00815119)
07.1 : NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00813694)
<SNIP>
07.22: NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00801856)
07.23: NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00813539)
08.0 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH4L9AA)
08.1 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH4G5JA)
<SNIP>
08.22: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH51J8A)
08.23: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH5044A)
Shelf 5: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 6: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 7: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 8: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Slot 1, port B:
slot 1: SAS Host Adapter 1b (PMC-Sierra PM8072 rev. C, SAS, )
MFG Part Number: NetApp, Inc. 110-00401 rev. A0
Part number: 111-02026+A1
Serial number: 031616001350
Date Code: 20160416
Firmware rev: 03.07.11.00
Base WWN: 5:00a098:006xxxx:14
Phy State: [8] Enabled, 3.0 Gb/s
[9] Enabled, 3.0 Gb/s
[10] Enabled, 3.0 Gb/s
[11] Enabled, 3.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00178+A0
QSFP Type: Passive Copper 5m ID:01
QSFP Serial Number: 610320089
01.0 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH5M99A)
01.1 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH3SWVA)
<SNIP>
01.22: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH527SA)
01.23: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH56XAA)
02.0 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1XN2Y)
02.1 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1YZGY)
<SNIP>
02.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1XVSG)
02.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1V8GH)
03.0 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TLAR)
03.1 : NETAPP X306_HAKPE02TSSM NA00 1695.4GB 512B/sect (K5HEVP9D)
<SNIP>
03.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1VARR)
03.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TH3C)
04.0 : NETAPP X306_HAKPE02TSSM NA00 1695.4GB 512B/sect (K5HEU7YD)
04.1 : NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TM21)
<SNIP>
04.22: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1TRZ3)
04.23: NETAPP X306_SMSKP02TSSA NA01 1695.4GB 512B/sect (Z1P1YYTT)
Shelf 1: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 2: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 3: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 4: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Slot 1, port C:
slot 1: SAS Host Adapter 1c (PMC-Sierra PM8072 rev. C, SAS, )
MFG Part Number: NetApp, Inc. 110-00401 rev. A0
Part number: 111-02026+A1
Serial number: 031616001350
Date Code: 20160416
Firmware rev: 03.07.11.00
Base WWN: 5:00a098:006xxxx:18
Phy State: [0] Enabled, 6.0 Gb/s
[1] Enabled, 6.0 Gb/s
[2] Enabled, 6.0 Gb/s
[3] Enabled, 6.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00177+A0
QSFP Type: Passive Copper 2m ID:00
QSFP Serial Number: 227921487
20.0 : NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJRBE5X)
20.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (NHGEH93Y)
<SNIP>
20.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (N8G7XTBM)
20.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (N8G7XU4M)
21.0 : NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJPZ6KX)
21.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (NHGEGGZY)
<SNIP>
21.22: NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJPVEKX)
21.23: NETAPP X477_HMKPX04TA07 NA00 3807.8GB 520B/sect (PEJR1W4X)
22.0 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JBNWDB)
22.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAEPNB)
<SNIP>
22.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAKZVB)
22.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JAZXKB)
23.0 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4J7MJEB)
23.1 : NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JBAP3B)
<SNIP>
23.22: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JDPD5B)
23.23: NETAPP X477_HAKPE04TA07 NA00 3807.8GB 520B/sect (K4JDNPPB)
Shelf 20: DS4246 Firmware rev. IOM6 A: 0181 IOM6 B: 0181
Shelf 21: DS4246 Firmware rev. IOM6 A: 0181 IOM6 B: 0181
Shelf 22: DS4246 Firmware rev. IOM6 A: 0191 IOM6 B: 0191
Shelf 23: DS4246 Firmware rev. IOM6 A: 0191 IOM6 B: 0191
Slot 1, port d:
slot 1: SAS Host Adapter 1d (PMC-Sierra PM8072 rev. C, SAS, )
MFG Part Number: NetApp, Inc. 110-00401 rev. A0
Part number: 111-02026+A1
Serial number: 031616001350
Date Code: 20160416
Firmware rev: 03.07.11.00
Base WWN: 5:00a098:006xxxx:1c
Phy State: [4] Enabled, 3.0 Gb/s
[5] Enabled, 3.0 Gb/s
[6] Enabled, 3.0 Gb/s
[7] Enabled, 3.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00178+A0
QSFP Type: Passive Copper 5m ID:01
QSFP Serial Number: 610320210
05.0 : NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0912384)
05.1 : NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0923740)
<SNIP>
05.22: NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0890897)
05.23: NETAPP X306_WKOJN02TSSM NA00 1695.4GB 512B/sect (WD-WCC1P0923803)
06.0 : NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1G9BA)
06.1 : NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1GANV)
<SNIP>
06.22: NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1FV2F)
06.23: NETAPP X306_SMEGA02TSSM NA00 1695.4GB 512B/sect (Z1X1FTYM)
07.0 : NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00815119)
07.1 : NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00813694)
<SNIP>
07.22: NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00801856)
07.23: NETAPP X306_WMANT02TSSM NA09 1695.4GB 512B/sect (WD-WMAY00813539)
08.0 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH4L9AA)
08.1 : NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH4G5JA)
<SNIP>
08.22: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH51J8A)
08.23: NETAPP X306_HMARK02TSSM NA04 1695.4GB 512B/sect (YGH5044A)
Shelf 5: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 6: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 7: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
Shelf 8: DS4243 Firmware rev. IOM3 A: 0202 IOM3 B: 0202
memory mapped I/O base 0x44810000, size 0x10000
memory mapped I/O base 0x44800000, size 0x10000